Chevrolet Cruze Forums banner

Forum Discussions about this Product

1 - 3 of 3 Posts
    1. · Administrator
      2014 LT program car, Pull Me Over Red, 1.4T Auto
      Joined
      ·
      14,181 Posts
      Discussion Starter · #56 · (Edited)
      How I removed and replaced my Rear Seats

      To start, I disconnected the battery with a 10mm socket and 3/8” ratchet. I removed the back-seat bottom by tugging on the end of the seat and gradually going toward the center.



      I then used a 15mm open end wrench to take of the three nuts under the center of the folding seat backs.



      With the nuts removed, folded the seat backs down. I then lifted the bracket up and gently pulled the seats towards the front seats creating a V between them.



      I stepped into the V opening with one foot and reached down and lifted at the intersection with the now unbolted bracket. I lifted, up and forward, at the same time until the seat swivel pin came out of the 40% seat.



      With the seats separated, the real work was to begin. I had read somewhere that all you had to do was push the seat back toward the door to get it out. It was
      not all that easy nor was it clear on how to disengage the spring-loaded pin. I struggled with this for quite some time. I tried screw drivers, brute force pushing while trying to lift. Nothing doing, especially by myself. I was getting tired when I hit a eureka moment. I ran downstairs and grabbed one of my longer reversable quick clamps. I quickly reset it to be a spreader and got to work.
      These are shots in sequence as far as what to look for but are of both sides. I just pieced this together to explain it. The first picture is the spring-loaded pin at rest. The second is when the seat is pushed towards the pin socket. The third is after it was removed and the fourth is an empty socket.



      To be able to lift out the seat, the pin needs to look like number two. In order to get it there, I used my quick clamp spreader.

      I lost this photo somehow

      This is after I popped out the first pin.



      I reset and pushed the 60% seat to get it out.



      Because I could not steady the spreader and lift at the same time, I used a prybar, as centered under the pin as best I could, to facilitate the lift. Now that the seat is disconnected, I set the 60% back against the front seats, so it will be out of my way even though it is still connected via the seatbelt.



      The next thing is to remove the nut holding the center passenger seatbelt. Remember the tab on the right and how it goes back together.



      The last part of the removal, for me anyways, was the airbag bolsters. I think it would make things easier if you take them out either before or after the seat bottom is removed. I found that grasping both sides of the top is easiest. When you are pulling, pull out perpendicular to the sheet metal behind the bolster. Remember that the bolster pivots out for removal. This picture shows the metal loop that is sandwiched with a plastic piece that is inserted into a plastic cup that is in a sheet metal hole.

      The second picture shows that the cup and insert is still in the hole as it did not come out with the bolster. I was able to reuse the clips this time. I ordered a pair of them just in case I damaged them. The third picture shows the lower mounting hole. [The plastic piece on the bolster just slips in, rotate the bolster towards the seat and clip in the top clip to install it.]



      The next thing to do to remove the bolsters is to unplug them. I found that a pair of needle nose pliers did the trick for me. I used a pair that the teeth were still decent and grasped the orange part and using my other hand, held back on the yellow part. It came apart very easily.



      Now that the seats are out, I set about vacuuming and cleaning up the melted Good & Plenty’s my daughters left me. (I think I have since found a better way to remove the seats, but I’ll explain this later.)

       

      Attachments

1 - 3 of 3 Posts

Forum Reviews

Be the first to review this product

Write a Review

Do you have experience with this item? Help our community members and share your knowledge.

Sign in to add review

Top