Just finished retro fitting a bose sub package I scavanged from a Wrecked Mazda 6 and I some how got everything working except one part.. I opted to run a relay for power and tapped into the speaker wires at the b pillar but I'm having a hard time finding a switched 12v at driver side kick...

Hello folks. I'm trying to find out which fuse location is a constant 12v so that I can hook up my dash cam and have it remain on/powered even while the car is off. I have seen several different how-to articles that show using a fuse tap with fuse 6/7, but the wiring I have already has a fuse...

Got a dashcam recently and I want the thing running 24/7. Has a g-force sensor on it but it's so sensitive that I close my door and it starts recording, even on different settings. So I had to shut that off. The battery doesn't last all day, so I was wondering if there was a way to keep the...

Earlier today I had an iPhone plugged in using a USB 12V adapter and a no name iPhone lightning cable in the 12V socket, a Samsung USB type C cable in my USB slot and a griffin aux cord all plugged in, previously this has never caused trouble. However this was the first time using this iPhone...

Hello I just got the blue Cruze RS like in the site banner and I was just wondering if there's more than one 12v & USB port? I have a radar detector that has a RJ-11 port to 12v plug, and then I have my dash cam that does both USB & 12v, then I have my phone charger which is usually USB to 12v...

Hey guys, I am trying to locate a 12v key on source (10-15a) to power my snow performance meth kit and trying to make things as clean as possible. I was thinking about using a fuse tap (or add a fuse) into the fuse box in the engine compartment since its right near the controller for the pump...

Hello, i have a question. I have checked up the Cruze Pinout Diagram and found only 12V Constant Battery and PIN43 Remote Enable. But the Remote Enable can not handle up to 500mah? Therefore i am searching another connection opportunities. Can someone pls help

Hi! I'm installing the LOC, but I don't know wichone of this bouch of cables is +12v to use with the LOC for the "remote". Anybody have a "color guide" or recomendation of which one can i use? Thanks a lot!

I'm installing an autodimming rearview mirror with LCD screen in my 2012 Cruze Eco. Here's the mirror:GM OnStar Auto Dimming Mirror with 3.5" Backup Monitor 9002-9510 - Mirrors. It requires a 12v signal when reversing. I've only had my Cruze for about 6 weeks and haven't poked around the...

So up until the past few days, the trunk, washer fluid and 12v accessory adapters worked just fine. Now, all at once, without any known reason, they all stopped working. Both 12v stopped working. I have two usb charging devices, one in each and neither now work, but the cable works elsewhere...

I installed my Glowshift gauges this past week, and they require a 12v headlight source to activate the 50% dimming feature of the gauge. You can't run anything that's on a dimmer switch, so all of the interior lights are out. Is there a headlight source inside the car that I can tap into to dim...

Gents Need to locate a 12V constant fuse. I would like to run off the internal fuse box if possible. Have plenty of "add a circuit" parts on the shelf, just need to locate a good 10 or 20 amp fuse slot. Is the PWR outlet fuse N#7 or N#20 on the internal box constant 12V? If I need to I'll work...

Frustration, I've been working on the meth injection install for quite some time. I have been taking my time ordering the proper parts to make a very clean install. Now i can't find a clean way of hooking up 12v switched. Ideally i want to use one of the relays in the fuse box. If not use some...

hello just bought a gps tracker to the cruze. i have the wiring read to connect to a 12v source. the problem is that it has to be conected to the battery directly since every 12v sources in the car such as lighters, brake lights, etc etc etc...work only when the car is on and the gps tracker...

Hi, I need to add-a-fuse 15 amp in the fuse box in the engine bay (not the fuse box in the car driver side). I need a 12 v source when i turn the key to on. I dont want a 12v always on... Anyone can tell me where i can add my add-a-fuse? Thanks.