Chevrolet Cruze Forums banner
beam
1-13 of 15 Results
  1. General Discussion
    Hi, I replaced my headlights in a 2011 cruze eco. Before it was fitted with normal h13, 55/60W. I replaced with H13 80/100W. I did not re-adjust the lights in any way but now the dims are extra dim and the brights are where the dims used to be. My question is why must I re-adjust the lights when...
  2. Gen1 Audio & Electronics
    as in the title, my 2013 Cruze has a few problems. I guess they are related. Any suggestions, how to diagnose the issues?
  3. General Discussion
    Been driving a 2013 ECO for a few years now. Car has run great in all aspects. But just noticed that all headlights go off when I put on my high beams. Blue dash light comes on though. Read a very little about others having this issue. One YouTube`r suggests an easy install of a new fuse box...
  4. General Discussion
    Hello All, As i was turning into Waffle House I notice my right light was out. Inspecting it further....I notice the light does come on if its set to high beams.....which to me doesnt make sense considering both settings come from the same bulb so the light "should be on regardless of...
  5. General Discussion
    I just got off the phone with my local Chevy dealer and they weren't really much help. I am struggling to figure out why my hi beams wont come on even though the blue light in the dash comes on when the hi beams should be on. I checked the fuses and the headlamps and they are both fine so that...
  6. Gen1 Service Issues
    When I switch on the high beams-nothing glows-no highs, lows, or fogs. On low beam, lows & fogs work. There is no power under both high beam fuses #37 & #38 in checking them, but both are good. My Question is where is the high beam relay in the engine compartment fuse block-what number is it?
  7. CruzeTalk New Member Introductions
    Could anyone tell me if the high beams are positive or negative switched? I was told that you can check this by using a multimeter, however, I'm not real sure how this is done. I'm trying to install a headlight flasher because I'm a firefighter EMT, I want to do the headlight flasher system over...
  8. Gen1 Audio & Electronics
    Does anyone know if the low beams can be modded to stay on with high beams? I know the factory headlamp is a dual element bulb and not sure if this can be done with this kind of bulb. I have aftermarket headlamps where I have 2 seperate bulbs and was wondering if this can be done either way?
  9. General Discussion
    Hello everyone I am hoping someone here can help diagnose my headlight problem. When I turn on the high beams, the headlights and fog lights turn off. As soon as I turn them off again, the running and fog lights turn back on. Back in January I installed HIDs for both headlights and fog lights...
  10. Lighting
    I'm having troublites with my highbeams. I've been through multiple aftermarket bulbs and had no luck. Now i am using Lumens HIDs and still having the issue. My DRLs work fine, aswell as my low beams; however my high beams have worked everytime for a couple days, then quit. Do 2013 Cruzes have...
  11. Lighting
    I live in a dangerous moose/deer region and the hi beam on my cruze dont light enought. So, whats my option? I'm canadian and I need the drl I want the lightest hi beam sorry for my english, im french
  12. Lighting
    Hi all, I just installed a HID kit from Retro-solutions that comes with a relay harness. Everything works fine and my DRLs are working too but it seems like the high and low beams are reversed! I searched the forum and found this thread...
  13. Lighting
    I just picked up a HID kit on eBay. Bi-Xenon, the bulbs tilt for high beam and low beam, but it seems to be reversed. So the cutoff for low beam is where high beam should be and vice versa. Can anyone think of a way to "trick" it back into the proper config? I've tried a few things, but they...
1-13 of 15 Results
Top