Chevrolet Cruze Forums banner

bolt

  1. Gen1
    I have a 2015 Chevy Cruze LT. One of the shops tightened them to the point of stripping. I am trying to find the proper ones. Can anybody help point me in the right direction, please? It's hard to get them on and off.
  2. Gen1 1.4L Turbo
    I recieved my new ignition coil pack and am about to install it. However, the old pack is missing one bolt. I can’t find any information to identfiy the bolt, anybody know the kind of bolt I need and where I can get it? Do I have to special order it from GM or will the dealership possibly have...
  3. Gen2 Powertrain
    Installing throttle body spacer and found this hole for a bolt just to the passenger side towards the front of the car of the throttle body. Anyone know what it might be for? Sent from my iPhone using Tapatalk
  4. Gen1 Appearance, Body, Detailing, & Interior
    Does anyone know the torque specifications for the four bolts holding down the front seats and the three nuts for the rear seats? I also need a part number for the blaack plastic post seats for the headrests. That would be the long deformed thing in the picture.
  5. Gen1 Wheels, Tires, Brakes, & Suspension
    They told me at the dealership that the bolt pattern on the 2013 Cruze is different then on the 2019 Cruze. Is this true? When I measured they appear to be the same, I don't know if I am missing something here. If I am not mistaken, I think the 2013 Cruze has a 5x105 bolt pattern.
  6. Gen1 Powertrain
    Hey Guys! I replaced my valve cover gasket on my 2012 Chevy Cruze 1.8L today and went to tighten the last bolt and....SNAP. Does anyone happen to know what size/thread bolt it is? I did some looking online and in this forum and I can't really find anything specific. It's one of the shorter...
  7. Gen1 1.4L Turbo
    Hello, I am trying to get the head off. What a job! I bought the kit to lock the cam, crank and timing chain in place. I am now down to removing the head bolts. After searching here and other sites, I could not find the correct size socket to remove the bolts. I mistakenly used an E-14...
  8. Gen1 1.4L Turbo
    Hello all, I was wondering if I could get some help examining a transmission fluid leak on my 2013 Chevy Cruze Eco 6spd manual 1.4t with 100k miles. I know for sure my MTF is leaking due to when I did my first drain, only 1.25qts came out. I decided to put MTF dye into my fluid to examine...
  9. Discount Tire Direct
    There are arguably more aftermarket wheels available today than ever before - but how do you know which ones fit? Your vehicle requires a wheel with a specific bolt pattern in order for it to safely fit. This is determined by the number of bolt holes the wheel has and how they are spaced...
  10. Gen1 1.4L Turbo
    anyone have any tips on extracting a broken seized bolt in the head for the coolant outlet? can a small torch be used?
  11. Gen1 1.4L Turbo
    Hello, I recently replaced the valve cover on my GF's 2012 chevy cruze 1.4L turbo due to a ruptured vacuum regulator diaphragm. and the valve cover replacement went smoothly except for one issue: I overtightened the bolt on the top center, passenger side of the cover (image at...
  12. Gen1 1.4L Turbo
    The turbo oil feed tube has banjo bolt and washers on one side. These washers are used on the coolant lines running into the back of the turbo as well. I am having a hard time tracking down these numbers. They are bonded rubber-metal washers, 10.1mm inside diameter (rubber), 18.1mm outside...
  13. Gen2 Wheels, Tires, Brakes, & Suspension
    Are the gas and diesel Cruzes the same 5x105 bolt pattern?
  14. Gen1 1.4L Turbo
    Hey there, 2011 Chevy Cruze 1.4 Liter Turbo LT So long story short whilst replacing the valve cover gasket one of the bolts that are on the valve cover got cross threaded. The bottom two rows of the bolt broke off. Now it won't screw back in securely. (My fault obviously). It now leaks from the...
  15. Gen2 Service Issues
    I have a 2017 Cruze Hatch Lt and i am trying to find the engine bolt specifications for rebuilding the pistons and rods. Can anyone help with this? My Cruze has a cracked piston in Cylinder one at 15K miles and im not wanting to pay the dealership the $3500 they are wanting to fix the problem...
  16. Gen1 Wheels, Tires, Brakes, & Suspension
    Does anyone with access to a GM Parts Catalog know the part number for the bolts that hold the brake caliper bracket to the steering knuckle? I asked the dealer by my house and they refused to give me the part number. I also called a couple online parts suppliers and they also refused to give it...
  17. Gen1 Wheels, Tires, Brakes, & Suspension
    Made an attempt to upgrade shocks only to come to find the bigger bolt at the bottom of the stock shock absorber in the rear wouldn’t even budge with a breaker bar. Has anyone else faced this? What method did you use to remove them? What size socket? Thanks.
  18. General Discussion
    Can anyone tell me the head bolt tightening sequence for a 2013 Cruze LTZ, 1.4L? Not having much luck online.
  19. Chevrolet Cruze News and Reviews
    Read more about the 5 Unexpected Things That Happen When You Autocross a Chevrolet Bolt EV at AutoGuide.com.
  20. Gen2 Diesel General Discussion
    The 2014 diesels had a 5x115 bolt pattern while the gas cruze had a 5x105 bolt pattern. Does anybody know if both gas and diesel 2017's have a 5x105 bolt pattern? Dealers here have no clue.....
Top