Chevrolet Cruze Forums banner
bolts
1-17 of 19 Results
  1. General Discussion
    Question one of my bolts for the ignition coils is missing and its on back order right now can i use any bolt from like home depot that is matched or does it have to be from GM because no one has them.
  2. Gen1 1.8L
    On my 2012 Chevy Cruze LS, One of my Exhaust Manifold Heat shield bolts has rattled out. The flanges on the bottom have rusted and snapped off (Not sure who at GM though two little dinky flanges were a good idea) so my heat shield is being held by only one bolt. Can any one tell me the bolt...
  3. Gen2 Wheels, Tires, Brakes, & Suspension
    Ok, I have done stuts before, but have never had this problem. I cant get the bolts out of the steering knuckle. Its a 2018 so no rust. Tried a impact gun, hammer etc and they didnt budge. Any ideas?
  4. Gen1 Wheels, Tires, Brakes, & Suspension
    Who has replaced the front caliper bracket bolts when changing rotor's ? Did you reuse the bolts ? If not where did you find them.
  5. Gen1 Appearance, Body, Detailing, & Interior
    Hi, I see half of my valve cover bolts are rusted. I only have 50K miles on my 2013 Cruze LT. Also, I see a lot of rust build up on those bolts that hold the engine shield I think. This looks like excessive rust for a 4 years old and 50K miles car. Should I worry? Is this normal? I need to...
  6. Gen1 1.4L Turbo
    Hi, My 5 yrs/100000 mi warranty will expire in a few months and I will take the car to a GM dealership to run an inspection, just in case they will see something out of the ordinary. I just hit 50000 miles and so far, I had to replace the bad smelling HVAC box, leaking water pump (3 times), and...
  7. Gen1 Wheels, Tires, Brakes, & Suspension
    Does anyone know where to buy the caliper bracket bolts? I keep running across info that says these bolts shouldn't be reused after caliper removal for a brake job. Any info would be helpful. Even my son's auto shop instructor can't find any.
  8. General Discussion
    Hello all! New to the forums here but have been coming here for quite a while in search of info on my 2012 Cruze LTZ. One of the T30 bolts on my ignition coil is about to strip out. Anyone know what type/size this bolt is? The only information I have on it is that it's a T30 Torx screw. Any...
  9. Cruze Parts
    Updated Camshaft cover with all bolts + gasket, Brand new right out the box still in the bag. Local pickup only, NE Ohio. ill meet halfway. 40$.
  10. Gen1 Wheels, Tires, Brakes, & Suspension
    Just put 20" kmc rockstars with 235/35/20 on my 2014 ltz and want to order the eibach pro kit. Was wondering when I take it to get a front wheel alignment do I need to purchase the camber bolts to keep my factory stance or is there enough adjustment in the stock.
  11. Gen1 Audio & Electronics
    Hey guys, I have a 4 gauge setup right now, but will be upgrading to 1/0 in the very near future. Quick question though. I currently have lugs on the power and ground wires. I cannot remember what the opening size is though for the ground. I used the bolts that hold down the top of the back...
  12. Gen1 Appearance, Body, Detailing, & Interior
    Well, here's my first post asking for a little help. Let me start my first saying I'm new, but I know how the search tool works and I've spent quite some time but haven't really found what I'm looking for. I was in the process of swapping out stock bulbs for LEDs last night, and went to do the...
  13. Gen1 Wheels, Tires, Brakes, & Suspension
    For those who dont know, the Cruze has no ajustement for Camber, front or rear. The positive is that even dropped 2.2 inches like mine, u can still have stock alignement. But when i looked at my tires, since im changing them real soon, i saw that my Driver side front tire was worn more on the...
  14. Gen1 1.4L Turbo
    So I was driving around yesterday when I heard a bang or knock type sound. As it became more frequent and louder I became alarmed and curious. So I went under the hood today and noticed right away that there was a bolt hole staring at me. Right next to it was a loose bolt. I wanted to see how...
  15. Gen1 Powertrain
    Just like the title says: Does anyone know what size of bolts are on the bottom of the dp that connect to the mp?? I am planning on swapping my dp as soon as it comes in from ZZP.. Any help or pointers will be greatly appreciated!! Thanks in advance..
  16. Gen1 Powertrain
    Last night I replaced the master cylinder clutch assembly in the SRT-4. While I was under the car, I noticed a ton of oil dripping. Further inspection shows it's coming from somewhere on the turbo but I can't figure out where or why. There is a heat shield on the top of the engine that shields...
  17. Gen1 Powertrain
    so i am waiting for my tune to get here from BNR (awsome people) and i decided to change my oil. it was just about time anyway. so i put the car up on the lift and up she went. started to look around making sure all is good and oh no...what....what is that! i found a lil less than a half quart...
1-17 of 19 Results
Top