Chevrolet Cruze Forums banner
crankshaft
1-18 of 18 Results
  1. Gen1 Diesel Technical Discussion
    Searching for a tool alternative. Does anyone know of an aftermarket alternative to the Crankshaft holder (EN-47630) and extension that will work on the LUZ? Thanks!
  2. Gen1 Powertrain
    Hey everyone, I had a crankshaft seal go bad, I removed the junk one and now I’m having a heck of a time getting the crank shaft pully back on. The hexagonal oil pump has fallen down and I can’t get it on, does anyone have any tips or advice to get it back on? Thanks!
  3. Gen1 1.4L Turbo
    Good Morning/Afternoon to all. Sunday April 21 my 2014 Chevy Cruze started to make a weird whistling noise. After researching this I found it to be the valve cover pcv diaphragm. I ordered the replacement Valve cover AND the replacement Intake Manifold and installed both of them to rule out any...
  4. Gen1 1.4L Turbo
    I've been researching a noise on my Chevy Cruze that started about a month ago. I thought it was a pulley or belt but I do not think it is. I watched a few videos of a front crankshaft seal failing so I tried to replicate the advice from the videos. When I pull the dipstick, there is a bit of a...
  5. Gen1 Powertrain
    I'm going to jump on the Cruze next week and replace the forward mainseal, which is chirping due to the pcv failure. Has anyone here done this, any tips, also does one need to use a puller? I ask because I just removed my honda odyssey flywheel the other day and didn't need to use one it...
  6. General Discussion
    Can anyone tell me where to find the crankshaft sensor on a 2013 Chevy Cruze ls 1.8 liter
  7. Gen1 Powertrain
    Hey guys like the title says, my check engine light is on in my 2014 LTZ and the thing barely starts, if at all. I waddled it to Autozone where they pulled the codes and they were for the Crankshaft Position Sensor and Camshaft Position Sensors A and B. Car only has 48k miles on it. It...
  8. General Discussion
    I've been having the same problem I see a few other people have been posting about with my 2012 crude LS. While driving (low speeds and high speeds) my car will jerk and I will get 2 separate device warnings on the dash. Service stabilitrak and service traction control. My RPM needle also drops...
  9. General Discussion
    I have 1.4L and 2 of the bolts hole in the flywheel leak oil So does this an gm has the hole to deep and have drilled into the main bearing oil journal Just saking
  10. Gen1 1.4L Turbo
    Hi everyone, I have a 2014 Chevrolet Cruze and a couple weekends ago, I noticed a whistling noise at idle after the car had warmed up on my way back home after a trip out of town. Shortly after, the check engine light turned on and the car lost power - it felt like the turbo couldn't deliver...
  11. CruzeTalk New Member Introductions
    I have a 2013 chevy cruze. Where exactly can I find the crankshaft position sensor
  12. Gen1 1.4L Turbo
    Hey everyone, A few months ago (~109,000 miles) i found my turbo oil feed line to be leaking in the usual spot so i replaced it along with my water outlet and overflow hose while i was there. I also had an issue with my TBPS so i replaced the whole intake manifold with new throttle body + fuel...
  13. Gen1 1.8L
    Hi all, after not torqueing the crank pulley/harmonic balancer back on the timing sprocket tight enough, the pulley sheared the cast alignment guide off. Thankfully that was all the damage that happened as the bolt had not spun out much before I picked up on the problem. Chalk another one up...
  14. General Discussion
    Here's a GM article for the 1.4L aluminum block engine that is being used in the Opel Astra. I find it interesting that they are building this with a cast hollow crankshaft? I'm assuming this 1.4L will be very similar to the new 1.4L in the 2016 Cruze. Can anyone confirm this hollow...
  15. Gen1 Diesel Technical Discussion
    Hi Forum members and readers. I thought I would post this topic to assist with other frustrated owners of a Holden (Australian) Cruze Diesel. I own a 2010 Cruze 2.0L SOHC Diesel and have been having issues with the vehicle just out of warranty. (6months and 5,000ks outside of warranty) Apart...
  16. Gen1 1.4L Turbo
    I just want to thank Rob for telling me I have a camshaft position sensor leak without even looking at my engine....haha. I mention my crankshaft seal is leaking behind the pulley and he tells me to check the cam sensor. Well looking at it from the front it appears normal but upon closer...
  17. Gen1 Service Issues
    Couldn't change the title on my phone so here's the revised code. TLDR: Crankshaft misaligned after oil change and tire rotation. Could they have done something to cause this and I should take back or it was just a coincidence and I should take to dealer much closer? Is that covered under...
  18. Gen1 1.4L Turbo
    Does anyone know where i can get detail drawings of the 1.4L Turbo Crankshaft Flange. We want to bolt a belt drive to it and the drive unit was made for the bigger Ecotec's. The bolt pattern for the flexplate is a little different the than the bigger Ecotec's. We are setting this engine to power...
1-18 of 18 Results
Top