Chevrolet Cruze Forums banner
fitment
1-17 of 17 Results
  1. General Discussion
    Hello, I have a stock 2013 Cruze LS. I was thinking about get some new wheels; the wheel is a 18x8.5 with a 42mm offset. (Tire size: 235/40R18). I want a poke fitment and need help picking up some spacers. I am also picking up the Eibach pro kit lowering springs If anyone is running a similar...
  2. Gen2 Wheels, Tires, Brakes, & Suspension
    I recently went from the stock 225/40/18 tire to a 225/45/18 tire on an 18 x 8 wheel with +40 offset that I was previously using. I wanted extra sidewalk and thought it wouldn’t be an issue but I’m rubbing the wheel well on my he front drivers side wheel and the can’t accelerate at high speeds...
  3. Gen2 Appearance, Body, Detailing, & Interior
    First off, I know the factory projectors are halogen projectors, so don't remind me. I am looking for beneficial information.... So who has successfully installed a LED kit and was able to use the factory dust cap? I'm not a fan of leaving them off. I read places that people used Diode...
  4. Gen1 Diesel General Discussion
    Do you guys know of any wheel spacers made specifically for the the CTD? I know the lug pattern is different (5x115) but I would also prefer them to be hubcentric.
  5. Gen1 Diesel General Discussion
    Before: After: Backspacing is perfect, 5x115 bolt pattern, and the hub is the perfect size. It is a 20x8" wheel with -20 offset. Wrapped in a 245/35R20 tire. Quick 10 minute ride says its firmer ride but turn in is vastly improved with much reduced understeer. Thinking of lowering...
  6. Gen1 Wheels, Tires, Brakes, & Suspension
    Hi guys, new to the forum and new to modifications. Could really use some help/suggestions. Ive been looking into putting some Corvette Sawblade Wheels on my Cruze (2011 LS Automatic) and I have a few fitment questions. Ive done a lot of research but am reaching out for help. My questions are...
  7. Gen1 Wheels, Tires, Brakes, & Suspension
    Looking for info on wheel fitment! Im looking for a stance fitment without all the camber ****. Wondering what offsets and tire sizes work the best with little to no rubbing. I want to stay with an 18" wheel but possibly an 8" wide in the front and 9" wide in the rear. Hoping someone has done...
  8. Gen1 Wheels, Tires, Brakes, & Suspension
    Ok, so the same rim, two different sizes/fitments. Which will end up pushing out further towards the fender? 18x8 35 19x8.5 40 They will be basically the same right? But the 19 1.5mm out and slightly closer to the edge of the fender, thus the tire size is more critical on the 19? I'm...
  9. Gen1 Wheels, Tires, Brakes, & Suspension
    i was looking into the Styluz M537 Satin Black rims, 18x8.5 +40, every site i go to says these wheels don't fit my 2014 chevy Cruze LT RS, can someone explain to me why?
  10. General Discussion
    JK!! my turbo for the trans am showed up the other day and i was too excited not to share with everyone :yahoo: its a precision 7675 and thats a pint can to give some size comparison, Maryland boys will respect the boh haha. anyways here she is cant wait to slap her on....which wont be for...
  11. Gen1 1.4L Turbo
    i have a 2014 cruze and found a used Injen CAI that says it was from a 2011 cruze. So far the little amount of poking around ive done ive only seen them sell for year ranges 2011-2013, but Im assuming this has the same fitment as the 2014, same mounts and everything. can anyone confirm or deny this?
  12. Gen1 Wheels, Tires, Brakes, & Suspension
    Okay I have a set of Enkei RPF1 18x8.5 5-114.3 ET30 with a 73mm bore I was wondering if buying a set of wheel adapters would help these fit on my ltz RS Cruze or would they stick out to far because of the low offset? Any help or information is appreciated just want to know if I should buy...
  13. Gen1 Wheels, Tires, Brakes, & Suspension
    im gonna get some new rims soon and there gonna be custom so im wondering how do you measure how much rim can you fit under the cruze,im not going huge,im going 17in but i want them to be staggered pretty much alot of offset,ill be getting stretch tires im going hellaflush
  14. Gen1 Wheels, Tires, Brakes, & Suspension
    Searching around earlier and I got some visual on some of the Australian guys using Team Dynamics wheels. I have heard of and had access to Team Dynamics wheels while I was racing the Focus and they definitely have some nice offerings that are lightweight. These are the same wheels that are used...
  15. Gen1 1.4L Turbo
    I just received intake today and installed it a couple hours ago. Had it done in an hour despite taking forever to get that rubber piece to fit the lip of opening, and an issue with splash guard. I pulled tire and splash guard off to install. Set it up, and went to put splash guard back on, and...
  16. Gen1 Wheels, Tires, Brakes, & Suspension
    hello my OEM wheels of my cruze are 7x17 with an offset of 44. ive found a really good deal for some 8x18 with a offset of 42. my doubt is if with this offset they will fit fine. thanks
  17. CruzeTalk New Member Introductions
    Hello all. My name is Jamie and I'm the lead designer at Doug Thorley headers. I'm interested in looking at a new cruze and possibly design some exhaust products on the car. This is not spam and I'm not trying to sell anything. When the time comes to promote the product, I will surely pay my...
1-17 of 17 Results
Top