Chevrolet Cruze Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-17 of 17 Results
  1. Gen2 Appearance, Body, Detailing, & Interior
    So I was going through the Chevy accessories page and saw that they had illuminated door sills for the gen2 Cruze. After scouring the internet I was unable to find an install guide or video on the sills. I have heard that they are held in place by magnets which has me even more skeptical about...
  2. Gen2 Audio, Electronics & Electrical
    So I have a bowtie shaped light that just gets power from a simple circuit. Basically you take off the bowtie, put on the glowtie, split the difference on all sides since its a little larger, then glue the orginal bowtie on top of the glowtie plastic piece. So next question. The glowtie is...
  3. Gen2 Appearance, Body, Detailing, & Interior
    Hello fellow Cruzers, Below is my first project of 2019. I always loved the look of the "Glowtie" on the new Camaros so when I saw they released it for the Cruze I was interested. It's a pricey mod for what it is so I initially put in on the back burner... Fast forward to last week I was...
  4. 👋 CruzeTalk New Member Introductions
    Has anyone installed the #13478514 illuminated sill-plates in a 2017 Cruze Hatch? If so, and you still have the instructions, it would be great if you could post them here since I want to see how the electrical connection is made. I was hoping that the connector would be below the factory sill...
  5. Gen1 Service Issues
    Well I got a strange occurrence today, while I am driving I get the dreaded CEL light on. So continue to run my routine drives & decide to drop by the Auto zone & let them run it once I am near there, well I had to make a few stops & turn the engine off & re-start well the engine light stayed...
  6. Gen1 Appearance, Body, Detailing, & Interior
    I'm at a GM dealership right now and was hoping they could install the illuminated door sill plates (the GM ones, not aftermarket). They told me it'd take 2 whole hours to install! Their labor rate is $134/hr and there's no way I'm paying $268 to have these installed! What I want to know is if...
  7. Buy/Sell Classifieds
    I have a GM illuminated sill plate kit, GM NEW in box. Bought to put on my car, haven't gotten around to it yet, don't expect to, plus I've got a wedding to pay for! Part number 95470931. I've seen them going on eBay for $250+. I'm selling my kit for $200 shipped. Looking to move this ASAP...
  8. Gen1 Appearance, Body, Detailing, & Interior
    I found the tiny trunk light a little dim, or when the trunk is full the light is blocked out completely. I have a bunch of rolls of LED strip lights lying around so I got to it! No need for details, the pictures are pretty self explanatory. I think it worked out pretty well. Didn't butcher...
  9. Gen1 Diesel General Discussion
    I recently traded my 2011 Eco 6MT for a 2014 CTD and while driving last night I had to grab something from the glove box... I noticed that the glove box isn't lit inside like it was in my old ECO. Not sure if it just doesn't work, or if they dropped that feature for the newer models?? Anyone...
  10. General Discussion
    Has anyone re wired the rear tails so both bulbs light up while pressing on the brakes? Jw, I'm looking to have this done come spring/summer.
  11. Gen1 Appearance, Body, Detailing, & Interior
    I just got a new bow tie and i have a couple of questions. How to take the old one off? and the best way to get wiring from my trunk deck to the battery. Also wanting to install a switch somewhere in the drivers side to turn the light on/off. thanks
  12. Gen1 Appearance, Body, Detailing, & Interior
    Hey everyone just got these installed today. They were an option on cruzes as a dealer install for about $550, but I picked them up for around $280 and wanted to install them myself. The install took about 5-6 hours, mainly because I couldn't figure out how to get the passenger knee airbag...
  13. Gen1 Service Issues
    I noticed in the last week that my low tire air pressure indicator was illuminated all of the time on my 2011 Cruze. It is showing that my tire pressure on my rear driver side tire is at 28psi. I have confirmed with several different gauges that my tire is at the mfg requirement of 35psi. How...
  14. Gen1 Appearance, Body, Detailing, & Interior
    Hello, I heard that that a guide was requested in how to install the sill panels in the chevrolet cruze. I bought them from my dealer for about 170 $ - so far I've only installed the rear parts, (easiest) but the front will come later on. This is what you get, with only a few tools needed...
  15. Gen1 Appearance, Body, Detailing, & Interior
    Just got back from the dealership and had some illuminated sill plates installed as well as some fog lamps. Here are some pics of the sills and the back of my ride showing the black vinyl overlay from GrafxWerks.com - Custom Automotive Products and a black RS badge.
  16. General Discussion
    Looks awesome to me! Fairly cheap and easy mod.here is the link to ebay if your interested in purchasing(no im not the seller lol) TAIL CAR BADGE LED LIGHT Emblem for Chevrolet Cruze - eBay (item 220715248810 end time Mar-25-11 07:45:05 PDT)
  17. Gen1 Appearance, Body, Detailing, & Interior
    Has anyone installed Illuminated Door Sills on a Cruze? I am thinking about either the official GM ones or aftermarket sills. The official GM ones only say Chevrolet but the aftermarket ones say Cruze. GM quotes .5 hours labor to install either non-illuminated or the illuminated ones, so...
1-17 of 17 Results
Top