Chevrolet Cruze Forums banner

loc

  1. Gen2 Audio & Electronics
    I am aware that many stock head units roll off the bass when the volume is turned up which is why many use an active LOC like a LC2i that can compensate for that before passing the signal on to your DSP or amp. These are not super cheap so figure it may be worth knowing if I could get by with a...
  2. Gen1 Audio & Electronics
    I have an Audio Control LC2i from my last car, but every build I see here uses the PAC LOC AA-GM44. I don't need the LOC part of that kit, just the harness. Does anyone know if that exists? I basically just need a portion of the stock harness with male and female ends to tap into. Can someone...
  3. Gen1 Audio & Electronics
    Title says it all. I already have an LC2i LOC from my last car and I'd like to do a clean, no splicing install. Are there other harnesses out there that work for our cars like this? I would actually like to run power from my amps through the stock speaker wiring if I can. Is there a harness that...
  4. Gen1 Audio & Electronics
    Just a quick look at what i have done to add rca's to the rear of the oem radio. i only added front rca's rear can be added the same way. i will add more details once i get a chance. but for now i had to cut a small piece of plastic at the back of the dash were the radio sits in the pocket to...
  5. Gen2 Audio & Electronics
    I have a 2017 Cruze LS and I am looking to add subs to the car. The LOC that was used for the 2016 Cruze does not work for the 2017s. Does anyone know which LOC would be used for the 2017s?
  6. Gen1 Audio & Electronics
    Hi everybody!. How LOC (Line out converter) works? I want to add a poweramp + subwoofer to my Cruze 2012. So I need a LOC But.. If I turn off the "bass" in the radio.. I mean.. If I turn bass to -12 to filter the low kick from my stock speakers... Whats happens with the subwoofer? ps: I'm...
  7. Gen1 Audio & Electronics
    What is UQA, I see the wiring diagram shows this and non UQA, I have the stock 6 speaker system with the 7 inch screen, Pillar tweeters and 4 6.5's, I happen to have all of the parts i need to add a amp to my new speakers my question is where do I tap into the wires. I see a area in the kick...
  8. Gen1 Audio & Electronics
    Its been quite a few years since I tackled audio installs. My daughter got a 2014 cruze and wants a sub put in. The things that have me stumped are which brand loc to use and how to wire speaker to match amp load impedance. I have seemed to search and research my self into audio coma. Here's a...
  9. Gen1 Audio & Electronics
    2011/2012 Holden Cruze (Australian) Standard audio system with dvd/sat nav from factory. I have a 6 channel Line out converter, currently planning on Splicing it into the left hand side kick panel main loom above the big plug, I have found the speaker wiring but before I start cutting into...
  10. Gen1 Audio & Electronics
    I did a quick search but couldn't find an answer, so here goes. I installed a LOC for my amp and sub with the factory head unit, but the remote wire seems to be on all the time. Per the LOC's instructions (which were not very helpful) I have the +12V connected to a constant source, ground is...
  11. Gen1 Audio & Electronics
    I'm going to start wiring up my new system this weekend, and the instructions for the Pac LOC are garbage, and the minidsp instructions are somewhat better but not by much. For the LOC, which wires do I tap into for power and ground? Should I buy a "add a circuit" for the #6 slot on the fuse...
  12. Cruze Parts
    I bought this GM44 LOC for easier sub installation. I can't make any further improvements to my car for the foreseeable future due to medical bills, so no reason to keep this around. New, never installed. $25 including shipping to CONUS. ETA: Sold.
Top