Chevrolet Cruze Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. Gen1 Appearance, Body, Detailing, & Interior
    Does anyone know how to replace the retainers that the roof molding clips on to? I had to replace those prices of trim because the somehow dried out and cracked. Well when installing the new ones the clips broke off in some places. Now the new trim won't stay flush.
  2. Gen1 Appearance, Body, Detailing, & Interior
    Hi all. My right side rocker panel modling on my RS model came unattached from the car. I don't know if the clips broke or what not but the piece isn't attached entirely to the car now and there is a space in between the rocker panel and molding. What can I do to fix this? the body shop...
  3. Gen1 Appearance, Body, Detailing, & Interior
    Hi all my 2012 Cruze LT RS rocker molding clips came loose or broke on my passenger side. Body shop glued it back to the car but that only lasted about a day. It'll cost me 400 to replace it now. I'm wondering if it isn't flush with the car and there is a space between the molding and the rocker...
  4. Gen1 Appearance, Body, Detailing, & Interior
    I removed the A Pillar Molding today so that I could get to the tweeters. I browsed all of the threads I could find on how to remove this molding and everyone said to just pull it off. I tried to be as careful as possible, but the small plastic tabs on the molding all broke when I pulled it off...
  5. General Discussion
    This is the wondow molding that is getting replaced this week by my dealership. Its all one piece, so im getting new glass too.( Just the smaller piece). Both rear door moldings and glass are getting replaced due to what we believe is premature aging. We looked at a dozen more cruzes and they...
  6. Gen1 Appearance, Body, Detailing, & Interior
    So while washing my car I had removed the black strip and sorta bent it a little. It's not very noticeable, but I know it's there. Anyone know where to get a new pair or where to order?
  7. Gen1 Appearance, Body, Detailing, & Interior
    I love the side profile of the Cruze,tonite in a parking lot a guy parked kinda close and I was like I hope he don't fling his door open and hit our car which he did not and it made me think.I was looking on Ebay and found "CHEVROLET CRUZE PAINTED BODY SIDE MOLDINGS 2011 2012 2013" they are...
  8. Gen1 Appearance, Body, Detailing, & Interior
    i was applying rain-x to my windows and noticed that the molding between the trunk and window looks like this. looks like maybe dry rot?? all other molding on car is jet black. im sure the dealer would say its normal but ill bring it up next time im in.
  9. Gen1 Appearance, Body, Detailing, & Interior
    Hello to All, I recently went to a park and drove over a low spot causing my driver's side RS rocker molding to get pushed up. Now the molding will not sit snug against the vehicle rocker. There is a approximately 1/4" gap on the top of the molding where it is supposed to fit tight against the...
  10. Gen1 Appearance, Body, Detailing, & Interior
    I am wanting to buy this rear lower bumper molding trying to get rid of the rear dull look but I guess the question is do I just removed the half looking cover and bolt this right up ????? eBay - New & used electronics, cars, apparel, collectibles, sporting goods & more at low prices
  11. General Discussion
    has anyone removed the grey plastic quarter window molding (the ones beside the rear seat headrests)? they have a plastic marker labeled airbag and im cautious of that. from the instructions it says its just clipped in place but the instructions dont show an airbag behind it. something is...
  12. Gen1 Appearance, Body, Detailing, & Interior
    Hi All, I bought off of ebay the Pillar Molding Set which looks pretty cool. It's supposed to stick on the plastic part on each side behind the rear windows. The Molding set comes with the 3M backing. Here's my problem,... I put them on when it was a cool dry day (Florida 78 degrees) and they...
1-12 of 12 Results