Chevrolet Cruze Forums banner

mount

  1. Gen2 Appearance, Body, Detailing, & Interior
    As we all know, hatchback models do not come with mounting points for the much sought after cargo net. I came up with a solution to this problem. PART LIST 1) Cargo Net: https://www.amazon.com/gp/product/B008FCD958/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 2) Mounting Points...
  2. Cruze Parts
    Up for sale is a freshly done, never installed urethane filled rear trans mount. This thing started off as a low mileage used mount and I bought a kit of liquid urethane to fill it up. This was supposed to be a cheaper alternative to a TTR mount and provide a more forgiving feel since its a...
  3. Cruze Parts
    Like the title states I'm looking for an aftermarket FMIC like zzp etc. Sent from my iPhone using Tapatalk
  4. Gen2 Wheels, Tires, Brakes, & Suspension
    Does anyone have a diagram/manual or jsut simply directions on how to remove the plastic cowl on a 18 Hatchback. I am needing to access the top strut bolt to remove the strut to finish swaping out the front OEM springs to the Ebiach springs.
  5. Vendor Deals
    <p class="p1">It’s no secret that there are a TON of smartphone mounts on the market right now, and given the sheer volume of dirt cheap offerings available across the web, it’s not always easy to separate quality from the junk that isn’t worthy of holding your long-dead 1st gen Motorola Razr...
  6. Gen1 1.4L Turbo
    Hey all, I'm about to replace the serpentine belt on my wife's car, but need more info on the motor mount bolts. 1. Are these torque to yield bolts? 2. What are the torque specifications for both the MM bracket to vehicle (3x) and MM to engine bolts (3x)? I've searched around and couldn't find...
  7. Gen1 Wheels, Tires, Brakes, & Suspension
    Hi all, first post here. I recently got a set of lightly used Pirelli tires for my wife’s car. Apparently the seller didn’t know one had a huge chunk missing from the rubber covering the bead. I went to get them installed today and Firestone said it was damaged too much to mount. Not sure if I...
  8. Gen1 1.4L Turbo
    Do you guys think I need a new lower engine mount? I hear a clunk when I accelerate from a stop and I'm not sure if it comes from the engine or transmission mounts. https://youtu.be/j6oY4Xhh01s Thank you!
  9. Gen1 Audio & Electronics
    Hi Guys, I have a 2014 Chevy Cruze LT with the my link. I bought the Kicker upgrade 200 Watt/DSP amp and decided to forgo the Kicker sub, instead I took my JL 500/1 amp and a 13" Focal Subwoofer out of my old car. I haven't mounted the amp yet, looking for a good spot. For those of you who...
  10. Lighting
    Hey All, I have LED glow under dash lighting and have been trying to get it to permanently mount but have had no luck. I don’t see any spots for them to zip tie to and no amount of any kind of glue is holding them in place . If anyone else has these lights and has had success mounting them...
  11. Buy/Sell Classifieds
    "used" because it was pulled out of its box and as such now has minor wear marks. $100 shipped to lower 48. Retail was $210 https://www.curtmfg.com/part/114393
  12. Gen1 1.4L Turbo
    I was changing the belt and tensioner and found a bunch of oil on the engine mount. (Some of it looked milky, mostly what was on the bolt). The engine oil is that low, just barely under full. Any suggestions anyone?
  13. Gen2 Audio & Electronics
    I have been looking for a potential way to hard wire my radar detector into my 2017 LT. It has the standard mirror and OnStar in the ceiling. Think there is a way to route a wire and pull power from the OnStar? I'm about to email MirrorTap and see if they have anything. FYI I am looking to do...
  14. Gen1 Wheels, Tires, Brakes, & Suspension
    what is the best offset / tire size for wheels that are 18x8? I have an Eco with stock wheels measuring 17x7. I want them to sit flush with little wheel gap. I also ordered KSport Coilovers so I will be lowering a bit. Any help is GREATLY appreciated. I would like them to sit like the attached...
  15. General Discussion
    Many states require a license plate on both the front and back of your vehicle. Michigan is not one of them, just the back here. Anyways my Cruze doesn't have a mount on the front. Can a dealer install an OEM mount? I would not be comfortable drilling holes. How much might something like this...
  16. Gen1 1.4L Turbo
    I stuffed some aluminum in the bottom of the front transmission mount on a 2013 Cruze 1.4T. The front transmission mount will lift up under forward acceleration, opposite the direction the wheels spin, this is why I stuffed something in the gap to prevent this movement upward. So far I have...
  17. TurboTechRacing
    Hello all! The rear transmission mount has just been released! It is a solid polyurethane bushing instead of the rubber bushing that comes stock, It will come with a how to manual aswell as i will be posting a video up on youtube of the actual installation of it. You can purchase this mount on...
  18. Gen1 Appearance, Body, Detailing, & Interior
    Easy project, but you do have to drill a hole in your fenders. Works with the turns only, I also modified the rear trunk mounted lights to also function as brake lights also. Never satisfied with the ordinary I guess. Always seem to modify or change-up stuff, from hotrods to choppers.
  19. Cruze Parts
    Thinking about selling some stuff. TTR upper motor mount, used for 2 summers. Silver mount, with red bushing. Comes with the included bolts and instructions. $150obo. Ported intake manifold, with slightly ported throttle body. also includes fuel rail and injectors. $180obo. Can send pics, and...
  20. TurboTechRacing
    COMING SOON! Chevy Cruze Lower Rear Transmission Mount!
Top