Chevrolet Cruze Forums banner
position
1-20 of 38 Results
  1. Gen1 1.4L Turbo
    No vacuum leak was detected after filling engine with lots of smoke at 3 psi. Then why the low vacuum reading on the gauge? And why the high Long Term Fuel Trim? Perhaps ECM is advancing timing too much due to faulty data from one of sensor data streams the it uses to control camshaft position...
  2. General Discussion
    What's the difference between PID's for Absolute Throttle Position vs. Relative Throttle Position? Trying to figure out what type of value to look at for the 1.4L turbo engine, when fully warmed up, sitting at idle. 19.2% Absolute. Is that high and require a cleaning or inline? That's...
  3. Gen1 Diesel General Discussion
    Hello everybody, reading this great forum has helped me to solve many questions regarding my Cruze and I am sure, you will be able to help me out on this one also. My Chevy Cruze is 2012, Korean made, for Europe, 2.0, 163 hp, 155.000 km, manual transmission. The issues I have are: When...
  4. General Discussion
    I've been having the same problem I see a few other people have been posting about with my 2012 crude LS. While driving (low speeds and high speeds) my car will jerk and I will get 2 separate device warnings on the dash. Service stabilitrak and service traction control. My RPM needle also drops...
  5. Gen2 Service Issues
    I rotated my tires and now the sensors are reading in the wrong location of the vehicle. Googled how to enable re-learning mode on the gen 2 Cruze and found nothing. Anyone know how to have the car register the new location of the TPMS sensors?
  6. Gen1 Audio & Electronics
    i ordered a new genuine GM brake position sensor since i do not trust aftermarket. the reason is when i press the brakes the brake lights flicker until i press harder on the pedal. there is no codes and even pressing harder if i slightly move they flicker again, i am thinking the sensor has poor...
  7. Gen1 Service Issues
    Hello everyone, I am hoping to get some advice about an issue I had with my Cruze earlier today. The check engine light came on and I had it read at an auto parts store. The code that showed up was P2135 which indicates a throttle issue. From what I have found online, it says it could be the...
  8. Gen1 Appearance, Body, Detailing, & Interior
    My question is this: what position should the window be in when connecting the new regulator to it? I've replaced eight of these in the past on a Grand Prix. It didn't care about the position. Should I treat te Cruze the same? Or is there a preferred position?
  9. Gen1 Wheels, Tires, Brakes, & Suspension
    I found instructions to perform a Brake Pedal Position Sensor Calibration. Calibration Procedure Apply the parking brake. Ignition ON, engine OFF, place the transmission in the PARK position for automatic transmission or NEUTRAL position for manual transmission. Install a scan tool. Clear all...
  10. CruzeTalk New Member Introductions
    I have a 2013 chevy cruze. Where exactly can I find the crankshaft position sensor
  11. Gen2 Appearance, Body, Detailing, & Interior
    Hi folks, Just got my 17 Cruze. This is my first Chevy- I've always been a Ford guy, and my 2016 Fiesta will probably be the last one I ever buy. That car was a nightmare. I digress..... I'm 6' tall with a 30" inseam (Longer legs, shorter torso) and I'm still trying to find a comfortable...
  12. Gen1 Powertrain
    First off: 2014 Cruze 1.8l LS ~66,000mi K&N is the only "mod" Recently got a CEL. Code P2076. All of my interweb searches point to either MAF or TB Assembly. I called Dealer and they said neither would be covered under the powertrain warranty. Of course, he'd be glad to run diagnostics for...
  13. Gen1 Diesel General Discussion
    Well I was on SI today trying to diagnose an issue with my remote start when I saw this memo that was issued today. For the record I had my dad do mine and have not had any issues. I am going to leave the current ECM program in my car unless I have any issues in the future. PS I think my remote...
  14. Gen1 Service Issues
    2014 1LT with manual trans. 23K miles. On the way to work in the morning I get an intermittent "Service Stabiltrak" error. This is followed by "Engine Power Reduced" and a Check Engine light. Turning off the car for 10 seconds clears the error. Happens a few times per week. Always in the...
  15. Gen1 1.4L Turbo
    Hi. I have been with the forum for 3+ years. Now I have lost my password, I have my email address. Is it possible to retrieve my old password? I have the old passwork as 9 character word with only letters and numbers. I have registered a new account and when I was setting up the password...
  16. Gen1 Engine/Transmission Tutorials
    How-To: Replace CPASV (Camshaft Position Actuator Solenoid Valve) Seals Overview: Yes, I needed to make up an acronym for this one. Moving forward, let's just refer to them as CPASV seals. I found these seeping on my 2012 Cruze at 58,000 miles when I noticed a slight oil loss (about 4oz in...
  17. Gen1 Service Issues
    2012 Chevy Cruze Eco 1.4T Manual 6-Speed 188,000Miles No Mods Hello, I am looking for guidance on what to check for the following symptoms. On a fresh start up my car's gear positions are just as they should be. I back out out of the driveway just fine, first gear and all initial upshifts...
  18. Gen1 1.4L Turbo
    14 Cruze ltz RS 25k miles, used obd2 to log small stuff and noticed at wot my tps only reads a max of 70% throttle. I have noticed it seems down on acceleration and this has me thinking more. I fixed my earlier post issue, returned intake to stock, cleaned maf with contact cleaner all while...
  19. Gen1 Wheels, Tires, Brakes, & Suspension
    I switched my headlights to OT7 Bullet HID. After I did this I had to put in the relay and the error capacitors because the check engine light came on. I went to the auto part store to get it cleared off and they said the brake pedal position sensor was bad. Would this have something to do with...
1-20 of 38 Results
Top