Chevrolet Cruze Forums banner
pulley

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-14 of 14 Results
  1. General Discussion
    My compressor coil went out on my 2012 so I ordered a used compressor that came from a totalled Cruze. I put the pag 46 in and bolted that sucker on there. The pulley spins fine when the belt is not on it, but when I tension the belt and turn on the engine, the pulley does not spin! It's the...
  2. Gen1 Service Issues
    I have 2011 Cruze LT 1.4L TURBO. Found my belt was shredding. I replaced today and when I fired it up, the cooling fan sounded like it wanted to take off and about 45 seconds later, the brand new belt started to shred. What is doing this??? Thank you in advance.
  3. Gen1 Service Issues
    So I had the normal chirping from the front crankshaft seal on my 2014 1.4t and decided to replace it. Looked easy enough in the videos. Put it together and all was well. Until I drove it 50 miles or so. It starting spitting oil around the seal and then a mich louder chirping/screeching noise...
  4. Gen1 Service Issues
    I'm trying to replace my idler pulley, very frustrating. Bought one online bolt didn't fit through new one. All these parts say they are compatible but are not. Chevy dealer can't give me part number (company policy) BS. Autozone has no part number for it, just whole assembly...........local...
  5. Gen1 Powertrain
    Hi, My 2014 cruze has 92,000 miles with a squeaking serpentine pulley, the belt was replaced about 3 months ago, not the pulley. The question I have is this something that needs to be replaced as soon as possible? The squeak sounds like a hamster on the little circle wheel. I had dodge vehicles...
  6. General Discussion
    What is the piece inside the spring for?mine is loose and rattling
  7. Gen1 Powertrain
    I'm going to jump on the Cruze next week and replace the forward mainseal, which is chirping due to the pcv failure. Has anyone here done this, any tips, also does one need to use a puller? I ask because I just removed my honda odyssey flywheel the other day and didn't need to use one it...
  8. General Discussion
    My car has developed a chirp/squeak. It's coming from the belt side and the only logical thing I can think of is the idler. Pricing parts I've discovered that they range from 40-140 at local parts stores. I did see one on the net that's says original gm, for $33. Looks like I may order that...
  9. Gen1 Powertrain
    I bought new Chevy Cruze at the end of 2011 and only now got to over 20000 miles. Few days ago my serpentine belt snapped. Luckily guys from repair shop said that all I need is new serpentine belt. However, during replacement they pointed out that my pulley is way wider than belt. They asked if...
  10. Gen1 1.8L
    Hello from Arizona, New to the forum and this is my current situation. Doing the timing belt on my 2011 1.8L automatic Cruze LS, but I can't seem to get the crank pulley off. Questions are... 1) Is the E18 torx bolt reverse thread? 2) Is there a tool to hold the motor to keep it from...
  11. Vendor Deals
    WHERE WE STARTED We hinted at these before, and many of you showed interest here... http://www.cruzetalk.com/forum/34-1-4l-turbo/129314-possible-pulley-development-nonstoptuning.html ^ feel free to read through that thread if you'd like to get caught up ^ WHERE WE ARE NOW We've reached a...
  12. Vendor Deals
    NonStopTuning Cruze & Sonic | 1.4 TURBO | Crank Pulley Group Buy WHERE WE STARTED We hinted at these before, and many of you showed interest here... http://www.cruzetalk.com/forum/34-1-4l-turbo/129314-possible-pulley-development-nonstoptuning.html ^ feel free to read through that thread if...
  13. Gen1 1.4L Turbo
    Hi everyone! Mike here from NonStopTuning | NST USA. As some of you may know, and have on other cars of yours, NST offers a variety of products for popular makes and models, mainly our lightweight line of aluminum pulleys. I'm curious to see if any of you here would be interested in a...
  14. General Discussion
    We are always willing to make pulleys for new applications/engines or bring old parts back but with the economy being what it is we can’t afford to sit on product and hope it sells. If 50 interested owners can be assembled we can make a crank pulley for roughly $200-250 depending on its...
1-14 of 14 Results
Top