Chevrolet Cruze Forums banner
pvc
1-14 of 15 Results
  1. Gen1 Powertrain
    Hi all, I have a 2014 lt1 w/ 38k miles (no that isn't a typo). Last year I my pcv went out and the vaulve cover was replaced. I'm prety sure they did not check the check vaulve at the intake to see if it was clogged at that time. But it seemed to fix the problem at the time. Last month (and...
  2. General Discussion
    The valve cove is bad and it is suck in air.When i put my finger over where it is sucking in air the engine wants to stall out. need help
  3. General Discussion
    My 2013 Chevy Cruze has code P0106, P015B, P0171,P0496,P1101,P0131. I have the valve cove PCV leaking. replace it once i get it. will i need the intake manifold as well and had bad are they to replace. Now are all then code caused my the PCV
  4. Gen1 Service Issues
    Hello all, first post as I am new around here. I have a 2012 Cruze 1.4T with 145K miles on it. I was experiencing a rough idle along with a couple engines codes that popped up. After reading some other posts on here, I determined that my check valve in the intake manifold went bad and caused my...
  5. Gen1 1.4L Turbo
    Anyone use a different setup other then keep replacing the factory hose?
  6. Cruze Owner Projects
    install pvc board 我從使用 Tapatalk 的 SM-N950U 發送
  7. Buy/Sell Classifieds
    I purchased the kit from xtreme and I didn’t install it. I just couldn’t get the manifold off and can’t get help from him so I’m selling the kit.first 60 gets it.I’ll take Paypal only or cash if you’re near wilmington,NC.
  8. Gen1 Service Issues
    way back around 65,000 miles the pcv system failed on my Cruze (2012 LT- 1.4L/manual shift). I didn't think too much about it as it was repaired under powertrain warranty. Last Thursday, I was driving the car and it just felt wrong. Idle was off, no power, laggy input on the throttle, jerkiness...
  9. Pvc

    Gen1 1.4L Turbo
    Hey, I'm venting!!! What freakin genius at GM decided to make the PVC part of the value cover, so when it needs to be replaced (PVC), you need to change the valve cover.
    pvc
  10. Gen1 Powertrain
    Mystery leak: I recently replaced the turbo oil feed line on 2011 80k+ 2lt rs package Cruze. Oil has stopped seeping from that line but the noxious smell of burning oil remains at idle and intensifies with the heat on. Oil is clearly leaking into or onto the exhaust but from where I'm not sure...
  11. General Discussion
    Hey Guys, I have a somewhat silly question. I been noticing my MPG were going down and just contributed it to me driving like a pissed off teenager. Then Friday my check engine light came on, and I got a code of P0171. It turned out being the PVC pipe in the car had a hole and was messing with...
  12. General Discussion
    PVC crank case vent tube Does someone have a direction and how it operates the PVC crankcase vent tube. I believe it goes toward the intake for flow and is checked flow toward the turbo. Another wards if there is vacuum on the intake it will not allow it to pull from the turbo. But when the...
  13. General Discussion
    My 2014 Chevy Diesel engine light came on again. This is the third time. Each time it was a sensor. This time its the PCV sensor so that is what the advisor told me at AutoNation Chevy Airport in Orlando. They have had the car now going on 3 weeks. They are telling me the part is on back...
  14. Gen1 1.4L Turbo
    ever since my pcv was replaced, and improper installation of the valve cover resulting in oil spraying all over the rear of my engine bay, my over all average mpg has seemed to drop from 29.5-30 down to 26-26.5 any ideas as to what could have caused this? my driving style hasn't changed at all...
1-14 of 15 Results
Top