Chevrolet Cruze Forums banner
1 - 4 of 4 Posts

·
Banned
Joined
·
10,296 Posts
All the symptoms of lack of a power on reset or a glitch in the electrical system causing the computer to crash. Ignition relay, battery terminal connection, or even an old battery that still starts the engine, but only has a capacity of about 15% left.

Would get your Cruze far away from a tire dealer. Other problems related to just the AT are dirty contacts in the brake switch, or what they use to call the neutral safety switch, or even in the PCM computer connector that all started with replacing all those expensive components in a non-electrical transmission like the governor, vacuum modulator, and that very complicated control valve with an 89 cent microcontroller. Far simpler today with just some control valves, but yet the price of these things skyrocketed.

Don't know how many people got screwed by getting their transmission replaced because the only problem was a dirty contact. Mechanical problems are consistent, electrical problems are erratic, your explanation of your problems are indubitably erratic. Minnesota, road salt, the electrical connection to your transmission is exposed to this crap.

Even tried to screw my own kids saying they needed a new transmission when a few checks showed dirty pins, some say you need a new computer for over a a thousand bucks, when the only difference between yours it has clean pins. But this is only on the male connector pins, not on the female pins inside of its connector that are also corroded, so this repair is only short term.

Now to find a Chevy dealer that knows just a little bit about electricity and is honest, this could be a problem. And you may not get a trouble code, ohmmeter sure works and not really that much to check.
 

·
Banned
Joined
·
10,296 Posts
Text Floor plan Diagram Technical drawing Plan


Here is a circuit diagram of the connector pins to the AT, if any of those pins are corroded, a control valve will drop out and you will be in neutral. Really can't say all shops are bad, but the ones my four daughters went to, really took a disadvantage of them. Firestone in Madison with a leaky tire said her ball joints were bad, 400 bucks,called me, bring it home. Did show her how the tire wiggled, the reason it did, they loosened the nut on her tapered wheel bearings, but sure managed to scare the heck out of her. Want to hear a lot more, maybe another time.
 

·
Banned
Joined
·
10,296 Posts
Since I had a manual transmission, not no need to look up the location of the so-called neutral safety switch they call it "Manual Shift Detent Lever with Shaft Position Switch Assembly", now.

Is located inside of the transmission, control valve cover has to be removed first after draining it.Sure makes sense for saving wiring, but not for maintenanceor even testing.
 

·
Banned
Joined
·
10,296 Posts
Since I still have the shop manual on this thing, says nothing about overhauling the automatic transmission, just some on testing the senors and control circuits. Worse than I thought, gummy solenoid valve, not full pressure on the clutches, slipped and toasted the clutch.

Since these unibody cars are throwaway, a ton of AT's are available from wrecking yards, some in the 300 buck range. If you plan on keeping this car. Maybe could find one with low mileage on it. Sure miss the dipstick, if nothing else to see the color of the fluid, can tell if its turning dark, time to replace it. Saved my kids AT's, and really because a strong believer in Lucas AT restoration products. Just by looking at the dipstick. Still can do this, but have to crawl under.

We purchased a use motorhomed, 1982 Chevy P-30 with a TH-400 AT in, wife was very anxious to take a trip, didn't fully check it out yet, A rubber coolant hose fell off, lost the fluid 300 miles from home, repaired the hose, and don't ask me how we managed to get home, but was toast. Drove up our driveway, then died, AT was smoking like crazy. But with this thing, could buy everything on the inside, and I mean everything, planetary gears, improved torque converter, all Made in the US Borg Warner parts for $480, ha, use to be 125 bucks, but we have inflation. With the shop manual was able to rebuilt it, but I guess they are not doing this anymore.

Kind of says to replace you AT fluid as recommended.
 
1 - 4 of 4 Posts
Top