Chevrolet Cruze Forums banner
1 - 6 of 6 Posts

·
Premium Member
Joined
·
267 Posts
Go back to COMG- The Cruze Owner's Maintenance Guide


I just got done installing GM fog lights on my '12 Eco and figured I would share how to do it without removing the front bumper. There are a couple other how-to's on this site that show how to do it by removing the bumper. For me that just wasn't an option, and IMHO is overkill. I am going to apologize for the bad picture quality up front. All I had was a cell phone to take pictures with.

Parts 1 through 7 are mainly concerning how to install it without removing the bumper. The remainder of them are generic to any fog light install.

You will need;
- T20 torex (for the front splash shield).
- Wire cutters/fork/something with a small edge to take the plastic inserts off.
- Philip screw driver.
- Small ratcheting wrench + 10mm + 1/4in sockets + 3in extension.
- Car ramps or a lift. I used wood ramps.
- Fog light kit (of course).
- Small hands is a plus.

Before starting make sure you disconnect the negative battery terminal, and the car is safely secured on the ramps or lift. I am not taking any responsibility for anything that happens to you or your car (or anything else) from following this.

1. Remove the front splash shield under the radiator.

There are a bunch of T20 screws that hold the front of the shield on highlighted in blue. These are easy to take off. There are 2 in the center that do not need to come off but I took them all off anywho.

The line in red are the plastic inserts. I used a flat head screw driver to get them started, then a wire cutters to get on both sides and pulled. They pop off pretty easily.

The green colored lines will need to come off also, but I did those later when I was installing the fog lights.

Lastly, the yellow arrow is the direction to pull to remove it. It should be self explanatory once you are doing this yourself. Basically just pull down and to the back of the car.



2. Remove passenger side non-fog light insert.

Once the shield is off I started with the passenger side first because it looked easier (and was). Removing the original non-fog light inserts was kind of tricky, but once you get a look at it things make sense. There is one screw holding it to the bumper. The 3" extension helped with getting more swing on the wrench.



3. Install the passenger side fog light.

This is pretty straight forward. Re-insert new fog light cover the way the non-fog light one came out. Once the insert is in place the actual fog light can be fitted. The fog light will slide right up there no problem. Once in there you can tighten down the two screws that go on the same side, or towards the center of the car, to hold it there while you get the third on the far outside. I used a wrench with a 1/4" socket and philips bit.

This step is where the small wrench comes in handy with an extension. The outside screw is in a place that is hard to reach, but it is doable (more doable than the driver side). This is also where I removed the screws/plastic inserts on the green line from the first picture. That allowed me to pull the extra plastic flat down (which is also part of the wheel well plastic) so I could get more of my arm behind the fog light.

Here it is installed.



4. Remove the driver side non-fog light insert.

It will come off the exact same way as the passenger side. For the temperature sensor I used a 10mm deep socket and pushed/gyrated it around the front side of the panel to pop the temperature sensor free.

5. Insert the driver side fog light.

The front panel and temperature sensor are another straight forward install, especially if you did the passenger side already.

The trouble comes from trying to screw in the outside far screw to secure the fog light to the bumper. This is where small hands is useful, and you will have to remove the screws/inserts in green from the first picture for this side. You just won't have enough arm room to get at the screw otherwise. I can't really explain how I got my hand up far enough, let alone with a ratchet, so I took a picture. Once all 3 screws are in you are finished installing the fog lights, and then on to the harness :)



6. Install the harness.

The harness is routed around the front of the car, next to the rest of the wiring that goes to the passenger side. There is a hole on the passenger side that the wire goes and drops down to the fog light.



The driver side has to go behind the headlight and the fuse end splits to the fuse box.



I attached the ground to one of the 3 posts that are to the inside of the driver side headlight. Then go back to the fog lights and plug them in.

7. Reinstall the splash shield

You should be done underneath the car now. Reinstall the shield the way it came off.

8. Install the switch.

Easiest part of the whole thing. Pop the fuse panel cover off below the switch and push from behind. Replace with the new switch. Sorry, no picture :)

9. Install harness to the fuse block.

Take the fuse cover off. The fuse you want is #48, 15A. There are three large stainless screws holding the whole thing down. Once they are loose you can wiggle the top portion off by unsnapping it from the 6 tabs on both sides. The fuse block top then wiggles off and you should see a bunch of holes where the fuse tabs would slide in to. There is only one end of fuse 48 present, and by comparing to the backside of the top you can figure out where it is suppose to go. The harness plug can be stubborn to get in the fuse block. I used a pointed needle nose pliers to make sure it was in all the way. Once finished, reverse the process to reinstall the fuse block. Again, sorry, no picture.

10. Do one last sanity check, connect the battery terminal you took off, and test them out :)

Hope this helped!

 

·
Premium Member
Joined
·
267 Posts
Discussion Starter · #9 ·
where did you buy the lights. GM or OEM.
I bought them from the dealer so they are OEM, and the correct style for the Eco. Ended up being $175 for everything.

That is true about the philips screws, it also helps when it comes off cause you don't have to rotate the wrench 180 degrees just to get it aligned again.
 

·
Premium Member
Joined
·
267 Posts
Discussion Starter · #13 ·
Sibby,
thanks for the terrific write up.
My lights arrived today (could so have used them on the way home).
So tomorrows project is to install them. Have my camera charged up so I can get a few pictures of how the wiring goes in the fuse block.
will let you know.
Bob
If you get some good pictures I could add them to the end of the how-to. Never hurts to have more pictures :)
 

·
Premium Member
Joined
·
267 Posts
Discussion Starter · #22 ·
I bought mine from the ebay link below.These are MUCH cheaper than buying them from the local dealer and the seller is a Chevy dealer so it is all OEM parts.Fog Lamp Kit for Chevrolet Cruze | eBay
Those are the exact ones I bought. Be warned though that the factory ones on my car said made in USA where those ebay ones say made in Korea, although they look and function the same. Not a deal breaker, but something I urked at.
 

·
Premium Member
Joined
·
267 Posts
Discussion Starter · #47 ·
Is it true that you have to go to the dealer to have the car programmed for lights? I read a few reviews on Amazon saying so, but haven't heard anything about it here in the forums.
It seems like most 2012 models did not need to be reprogrammed. Like 99_XC600 said, there is a specific date but I am not sure.
 

·
Premium Member
Joined
·
267 Posts
Discussion Starter · #50 ·
I'm looking at adding fog lights to my 2012 2LT. Does anyone have experience with the $70 ebay lights, or would I be better off spending $175 and getting them from a chevy dealer?
I recommend the legitimate fog lamps, and not the Chinese $75 dollar ones. The cheap ones come with a generic switch, and not the OEM one meant for replacing the head lights.

Just finished installing mine. The production date leads me to believe the dealer needs to activate them but when I press the fog lamp button, the fog lamp icon illuminates on the dash. Is this normal? The lights don't come on but I found it strange that the dash light would light up...
Check your wiring, primarily making sure the fuse and fuse wire is installed correctly. If the dash light is illuminated then the fog lamps should come on.
 
1 - 6 of 6 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top